Plasma Gas Guide .11.848.421.149 G125 For Kjellberg Hifocus Plasma Machine

Shanghai ZhouBo Welding & Cutting Technology company are a professional manufacturer of plasma cutter consumables, Our company is located in the Shanghai City, China ,it was established in 2007,but we had 10 years manufacturing experience in this field, the new factory covers an area of more than 10000 square meters .There are 50-100 workers and 20 research engineers.

We are a professional manufacturer of plasma cutter consumables.

Customer Satisfaction

If you worry about our products’ quality, I can give you some samples to test by free. Please don't hesitate to contact us if you have any questions or concerns before or after your purchase. We are committed to your 100% satisfaction.

Shipping and handing

1. DHL is our preferred shipping method. Meanwhile TNT, EMS, Fedex, UPS are available.
2. Make sure to leave telephone number when filling your buyer information.
3.You can check the goods where it is in transit through tracking NO .

Refund(Echange Only)

1.If you are not satisfied with your purchase, you can echange the items received. you must contact us within 5 days of the receipt

of your order. And you should pay all additional shipping fees incurred and the items returned should be kept in their original

status.

2.If you wish to echange defective or incorrect shipped goods, please contact us within 5 days after receiving the goods.

Notes

1. The buyer are responsible for any insurance you think necessary.

2. The processing time for a specific order varies with the product type and stock status. Mostly, processing time can be 3 to 15 working days.

Feedback

1.Since your feedback is very important to our business's development, we sincerely invite you to leave positive feedback for us if

you are satisfied with our product and service. It'll just take you 1 minute.

2.Please contact us before leaving any negative or neutral feedback. We will work with you to solve any problems.Thank you!

Technical Support:
How to maintain CNC cutting machine

CNC cutting machine working site and working environment is relatively poor, relatively large metal dust. Therefore, the machine must be fully cleaned and maintenance, the person responsible for the equipment lubrication, maintenance and maintenance work!


A. Safe operation:

1. CNC cutting machine is a sophisticated equipment, so the cutting machine operation must do sanding (man, machine, posts)

2 the operator must go through professional training and be able to skillfully operate, non professionals do not move.

3. In the operation must be confirmed without external interference, everything is normal, the cutting plate dipping in the cutting platform, the plate can not be more than cutting range (Note: in hoisting to be careful).

B. Daily maintenance and maintenance:

1. Each work, must clean up the dirt and guide rail machine, make the bed is kept clean, air and power is shut down work. At the same time emptying machine tube with residual gas.

2 if you leave the machine for a long time to turn off the power, in case of non professional operation.

3 observe the machine horizontal, vertical guide rail and rack surface with no lubricating oil, to keep the good lubrication!

C. Weekly maintenance and maintenance:

1 weekly to the machine for a comprehensive clean-up, horizontal, vertical guide rail, transmission gear rack cleaning, filling the lubricating oil.

2 check the horizontal and vertical rail cleaning device is working properly, if not properly and timely replacement.

3 check all the torch is loose, clean up the garbage of the ignition gun ignition, maintain normal.

4 if there is automatic adjustment of the device, the detection is sensitive, whether to replace the probe.

D. Maintenance of the month and quarter:

1 check the total air intake is free of garbage, each valve and pressure gauge is working properly.

2 check all tracheal joints are loose, all pipes with no damage. Tighten or replace if necessary.

3 check all the transmission parts are loose, check the gear and rack meshing situation, when necessary to adjust.

4 loosen up device, drive pulley by hand, whether freely, such as timely adjust or replace the abnormal situation.

5 check the clamping block, steel belt and guide wheel with no loose, steel belt tightness condition, when necessary adjustment.

6 check the electrical cabinet and operation platform, the fastening screw is loose, clean up the dust inside the cabinet with a vacuum cleaner or hair dryer. Check if the connector is loose (refer to the electrical manual).

7 check the performance of all buttons and select the switch, the replacement of the damaged, and finally draw a comprehensive detection of the accuracy of the machine.

            We are a professional manufacturer of plasma cutter consumables, Our company is located in the Shanghai City, China ,it was established in 2007,but we had 10 years manufacturing experience in this field, the new factory covers an area of more than 10000 square meters .There are 50-100 workers and 20 research engineers.

            In recent years, we have been sold in lots of countries and regions in Europe and Asia and gained good reputation widely with excellent quality . In order to meet customers’ requirements and improve product quality, our company has already realized mechanical processing numerical control automatization production, and been committed to manufacturing products with best quality.

           Our company adopts modern management mode and devotes itself to new high performance design and production of welding & cutting equipments, with continuous technique advantages innovation .All our staff are striving to realize the aim of "Create Chinese Brand ,Build First-Class Enterprise ",with the spirit of "Being honest and pragmatic ,making pioneering efforts and seeking perfection with persistency."

Company commitment: thinking what customers think, worrying what customers worry, in time delivery and high tracking service.